Looking for a Contractor?
Looking for a Contractor?

Alchatek Blog

John Ziebell

Recent Posts

Chemical Grout Durability

Posted by John Ziebell on Sep 28, 2021 10:00:00 AM

Banner - Chemical Grout Durability

Body - Chemical Grout DurabilityFor most of my 36 years in the chemical grout industry, I have listened to people refer to chemical grouts as temporary leak repair in the same manner they mention a band-aid in stopping bleeding. Many of these same persons also say that stopping water leaks with chemical grouts is like “smoke and mirrors”, implying some sort of black magic. I must state that they are wrong on both counts.  

The mechanism by which chemical grouts stop leaks is based upon basic textbook polyurethane and acrylic chemistry. It may seem a little mysterious because most of the reaction takes place out of sight within or behind the concrete structure, but the reactions can be duplicated in the laboratory for doubters to see. As for durability and permanence, the oldest of the chemical grout manufacturers have documented case histories that are now 50 years old. I would call these permanent repairs when compared to some leak seal alternatives.

It is true, however, that for every success story I offer, someone will bring up an instance where chemical grouting did not work. Upon careful examination, these failures are almost always due to the products being incorrectly specified or installed. The biggest problem I have encountered that leads to premature failures occurs when the contractor fails to pump grout into a crack or joint until total rejection occurs. That is the point where the crack will accept no more grout. Correct product selection and installation in consultation with the manufacturer are essential to a successful long-lasting leak sealing project.

Want more info on leak seal products and equipment?

Download the Info-Packed Leak Seal Product Catalog!

Topics: All Posts, Seal Leaks

Polyurethane Leak Seal for Basement Walls

Posted by John Ziebell on Mar 26, 2020 10:00:00 AM

Banner Graphic - Polyurethane Leak Seal for Basement Walls

Body Graphic - Polyurethane Leak Seal for Basement WallsToday’s guest blogger is John Ziebell, an independent representative of Alchemy-Spetec. Formerly the Vice President of Operations for Deneef Construction Chemicals, Inc., John has 36 years of experience in the chemical grout industry and is currently a member of the International Concrete Repair Institute (ICRI).

Recently, I visited a homeowner in Elkhart, Texas whose basement flooded after a heavy rainstorm. The house was three years old, and this was the first time water had entered the home. When we went into the basement, I saw that a water-repellent coating was applied to the below-grade walls during initial construction, but it was unclear if a water stop had been installed at the wall joint.

To test for the leak source, I suggested installing soaker hoses in the flower beds adjacent to the basement wall, flooding the beds for several hours, and confirming if water appears at the wall or floor joints. I also recommended two different options to prevent further leaks:

Option 1 – Polyurethane Crack Injection

If the cracks in the basement walls can be clearly identified and there aren’t too many of them, the contractor should use the polyurethane crack injection procedure. First, they’ll need to remove any surface contamination with a grinder. Then, they can drill holes spaced about 1 foot apart at a 45° angle to intersect the middle of the crack or joint and flush all of the injection holes with clean water until water runs from hole to hole. Once the water flow is confirmed, they can inject the crack or joint with Spetec PUR F400 (and GEN ACC Accelerator) until it’s completely full.

Option 2 – Polyurethane Curtain Wall Grouting

If cracks in the basement walls are difficult to identify the contractor should use the polyurethane curtain wall grouting procedure. First, they’ll need to remove any surface contamination with a grinder and drill holes in a diamond grid pattern (see photo included with this post). Then, beginning at the bottom of the wall, they can inject the holes with Spetec PUR H100 (and GEN ACC Accelerator) until they reach the top of the wall.

Many people ask if grouting only around the bottom next to the leaks is effective, but this is seldom the case. Grout is injected through the entire wall because any excess grout flows down over the previous injection area, creating a lapping effect like shingles on a roof.

Both options have their advantages depending on the situation: polyurethane crack injection is a cost-effective, pinpoint approach that is ideal for a small number of clearly identifiable cracks, while curtain wall grouting is a pricier approach that is ideal for a larger number of difficult to identify cracks.

Want more information on choosing the right leak seal products and application for your project?

Download an Info-Packed Leak Seal Methodology Brochure!

Topics: All Posts, Seal Leaks